• You can now help support WorldwideDX when you shop on Amazon at no additional cost to you! Simply follow this Shop on Amazon link first and a portion of any purchase is sent to WorldwideDX to help with site costs.

Search results

  1. project

    Cobra 29 receive on pa?

    Changed mic and problem went away. Found receive wire grounded against mic plug..
  2. project

    Cobra 29 receive on pa?

    The same thing except the audio comes from the external speaker.. Its strange
  3. project

    Cobra 29 receive on pa?

    i have a cobra 29 that receives on ps only amd have to switch to cb to transmit. The needle moves when switch is in the cb position like its receiving a signal but no audio. If I switch to pa I receive audio but can't transmit.. Any ideas??
  4. project

    12, 24, and 48 volts????

    Xforce has been sold. The new owner has more rf knowledge in his little finger than the previous owner (carol). Yes there will always be a place for class c boxes in 11m but expect big changes from xforce in the future.
  5. project

    11 meter coax for high power?

    Don't do that!! LMR 400 is fine and will last for years with better shielding and slightly lower loss . Hard line would be great if you can find it cheap somewhere but is way overkill for 1500w
  6. project

    dual base antenna's?

    I kicked around the idea of running two 8 element quads once. One at 1 wave length above the ground and the second one @ the second wave length on 2 separate towers about 50 meters apart. I had all the stuff to do it but never did. It seemed like a lot of work just for an experiment.
  7. project

    Painted Predator Antenna

    It's too close to the cab. Take your antenna and move it to the rear by the tail gate and watch the SWR fall flat. Just too much reflect off the back of the cab. I know it's scary but the best way to run that antenna is puck it!! I don't blame you if you don't want to drill a big ass hole in...
  8. project

    Randy Kokes #1 CB Tech In The Country

    Anyone else notice that out of all of the test equipment in the pic, none of it is turned on??
  9. project

    ¿ is height really might?

    I went from 40' to 160' and it made a huge difference in contacts.
  10. project

    Talking about amps ... who are the better ab1 manufactures?

    Like I said , If your a meter bater and want to see the needle swing as far to the rite as possible then you will need a fan but I don't fall into that category . I run everything within the design specs of the transistors and it will run that way for years. Just because someone tells you that...
  11. project

    Talking about amps ... who are the better ab1 manufactures?

    Like I said , If your a meter bater and want to see the needle swing as far to the rite as possible then you will need a fan but I don't fall into that category . I run everything within the design specs of the transistors and it will run that way for years. Just because someone tells you that...
  12. project

    Talking about amps ... who are the better ab1 manufactures?

    Why is that? You should be able to run that amp all day without over heating problems. There will always be heat generated by the transistors and the heat sink will absorb and dissipate the heat, that's its job. If a TS 350 is running hot enough to need a fan then there are other issues that...
  13. project

    Talking about amps ... who are the better ab1 manufactures?

    It's been my experience that if you have to add a fan then you are running it too hard. That heat sink is more than enough to dissipate the heat.
  14. project

    The most valuable commodity in the world?

    Although we can live without natural gas and oil, life would be very different without it .Computers, cell phones , tv's and just about every thing made from plastic would disappear but life would go on. Without water however, life would cease to exist all together.
  15. project

    Six pill High Drive Fat Boy

    I DK my 2x8 at 300w and let it swing . I don't think I've ever seen more than 12 or 1300w pep out of it. I could run the hell out of it but what's the point.
  16. project

    Grounding a Base Antenna

    My antenna is 160' to the feed point so where does that leave me?
  17. project

    Neighbor complaining about noise in his surround sound system . . .

    I run a yc156 tube (3cpx5000), and I don't bother anyone around. I have gone door to door and asked everyone and told them if they ever experience any problems be sure and let me know. Keep my equipment running clean and run well below the potential of the tube and don't have ANY problems. If...