• You can now help support WorldwideDX when you shop on Amazon at no additional cost to you! Simply follow this Shop on Amazon link first and a portion of any purchase is sent to WorldwideDX to help with site costs.

New Ranger 2950dx D6

So basically the 2950dx6 is just a 2950 capable of 100 watts and has a blue frequency display? Interesting. Might be going on my wish list, being I can do away with an in-line amp. No AM here, strictly SSB.
 
I agree 100% on the band coverage and being better built. If it's band coverage and "smooth" audio your looking for then go with the ham rigs. I only really talk on 11 meters (lower 38) for the skip into Europe and South America... and it's my Ranger 2970N2 that spanks my Yaesu FT-1000 MP MK 5 Field and my ICOM 706 MKII. Don't get me wrong...I'm not a big Ranger fan but I use what works for me. It's the 2970N2 that gets thru the pile ups with it's compressed audio...not the ham rigs. The Ranger doesn't have that "smooth audio" but when the skip is rolling in it sure gets thru the train wreck where the ham rigs would not. And for price..my Yaesu cost me 1100 used. My ICOM 706 MKII was 350 used my Ranger cost me 295.00 used. I run all my rigs thru big amplifiers So to each there own :) Everyone has different wants or needs and they should use what is best for them.
how do you Like the 2970 N2 compared to the N3 N4 i hear the N2 is the best built radio
 
Went to bells to check it out.. no price yet. This is a quote from the description.
"The new RCI-2950CD, rated at 50W PEP and the RCI-2950DX6, rated at 100W PEP are perfect for the recent band openings on 10 and 12 meters."
Aaaaa ok.... WHAT recent band openings??
Did you purchase one of these newer DX -6
 
Did you purchase one of these newer DX -6
No. If I do ever buy another one I would probably try to track down a nos 2950dx. Black/Green display. I liked my old one. Can't seem to dig the looks of the "cd" model display.. Had several old orange display 2950s & 70s back in the day. Lots of good memories.. Though the noisy receiver in all 29xx series radios leaves a lot to be desired.. I have a fondness for them.
 
No. If I do ever buy another one I would probably try to track down a nos 2950dx. Black/Green display. I liked my old one. Can't seem to dig the looks of the "cd" model display.. Had several old orange display 2950s & 70s back in the day. Lots of good memories.. Though the noisy receiver in all 29xx series radios leaves a lot to be desired.. I have a fondness for them.
The display looks a lot Easier to read in the CD model
 
  • Like
Reactions: Shadetree Mechanic
Ham rigs have adjustable on board compression and TX band width that can be narrowed on the fly to do the same as what you're doing. Ham rigs with a knowledgeable operator of his radio can get thru the same pile ups you're doing.

By the time your done going through menu's and adjusting the audio on your "ham" rig which just sounds stupid any radio an amateur radio operator is using is a "ham or amateur" rig the pile up will have already sorted itself out.

My President Lincoln from 1998 with my Ten-Tec 715 can bust a pile up faster than most people and even think about adjusting a complicated high end radio marketed towards amateur's as a 'legit" radio.

If I need to hammer nails into a wall to hang a picture a $20 hammer will get the job done just fine and while cheap is the best tool for the job. By the time I get a high speed dryway screw gun out I could have already had the picture hung.

Trust me I am not fan of the modern cheap as can be made RCI2950 but as a tool for 10m, 11m and 12m use it is an acceptable tool and for each weakness it also has strengths. It will never be an Icom or Yaesu but you can buy one new for $295 or less right now as I speak. It is not hard to improve on them either. Show me a proper dual band Icom or Yaesu mobile or base that you can buy new right now for $295 or less.
 
  • Like
Reactions: Slowmover

dxChat
Help Users
  • No one is chatting at the moment.
  • dxBot:
    Tucker442 has left the room.
  • @ BJ radionut:
    LIVE 10:00 AM EST :cool:
  • @ Charles Edwards:
    I'm looking for factory settings 1 through 59 for a AT 5555 n2 or AT500 M2 I only wrote down half the values feel like a idiot I need help will be appreciated