1. You can now help support WorldwideDX when you shop on Amazon at no additional cost to you! Simply follow this Shop on Amazon link first and a portion of any purchase is sent to WorldwideDX to help with site costs.
    Dismiss Notice

Search Results

Search Again
  1. Bub73
    Thread

    Yaesu FTC-1123, programming

    Yaesu FTC-1123 VHF handheld. Anyone know how to program this unit or where to find the info ? Thanks Bub73
    Thread by: Bub73, Jan 11, 2006, 0 replies, in forum: Ham Equipment
  2. Bub73
    Post

    Trouble shooting a Robyn SB-520D (NOMAD)

    Check the main board for 12 volts, if you find it try to follow it and look for cracked traces. Some of these would crack very easly even when...
    Post by: Bub73, Nov 6, 2005 in forum: General CB Services Discussion
  3. Bub73
    Post

    Trouble shooting a Robyn SB-520D (NOMAD)

    Check the on/off swicth and the PA swicth first, it maybe stuck in the PA mode shutting off everything but the pa speaker. Bub73
    Post by: Bub73, Nov 4, 2005 in forum: General CB Services Discussion
  4. Bub73
    Post

    Emperor 3010 no transmit

    Thanks for the reply; The voltage regulators seem ok and every thing runs cool . I don't know what voltages I should be seeing on the IC's etc....
    Post by: Bub73, Oct 15, 2005 in forum: General CB Services Discussion
  5. Bub73
    Post

    Emperor 3010 no transmit

    Thanks for the replys.... The mic and relay are working not much else in tx... Bub73
    Post by: Bub73, Oct 12, 2005 in forum: General CB Services Discussion
  6. Bub73
    Thread

    Emperor 3010 no transmit

    Anyone with a voltage chart for a Emperor 3010. I have one with no transmit in any mode. receive seems ok but no S meter bar graph and the PA...
    Thread by: Bub73, Oct 11, 2005, 5 replies, in forum: General CB Services Discussion
  7. Bub73
    Post

    Help!!!

    The center pin of the clarifirer is the one hooked to the wiper of the pot. It should be easy to find by using your volt meter while turning the...
    Post by: Bub73, Jun 20, 2005 in forum: General CB Services Discussion
  8. Bub73
    Post

    COBRA 25 LTD INCOMING AUDIO PROBLEM ?

    I would check the volume control pot also.......... Bub73
    Post by: Bub73, Jun 11, 2005 in forum: General CB Services Discussion
  9. Bub73
    Post

    Help!!!

    Thats where mine is, hope this helps... Bub73
    Post by: Bub73, Jun 10, 2005 in forum: General CB Services Discussion
  10. Bub73
    Post

    Help!!!

    The Black wire goes to the little ground strip that joins the two trimmer caps on the expo, the other end goes to the radios foil ground. Hope...
    Post by: Bub73, Jun 9, 2005 in forum: General CB Services Discussion
  11. Bub73
    Post

    Help!!!

    I'll look I may still have one of these kits stored away somewhere, It may take me a few days to find it. Bub73
    Post by: Bub73, Jun 9, 2005 in forum: General CB Services Discussion
  12. Bub73
    Post

    HR 2510

    Check the power cord and connectors first. I had a power cord that was damaged during storage........ Sometimes we try to hard and overlook the...
    Post by: Bub73, Apr 21, 2005 in forum: General CB Services Discussion
  13. Bub73
    Post

    Stacked 3 element yagi's ?

    Stacked 3 element yagi's at MURS freq's 151.820 -154.600. How do I figure the proper boom spacing for maximum gain? Thanks Bub73 </p>
    Post by: Bub73, Dec 22, 2004 in forum: CB Antennas
  14. Bub73
    Thread

    Yaesu 2800M

    Anyone know the mike plug part number for a Yaesu 2800M. I'd like to try a different mike and get away from the rf pickup problem of the stock...
    Thread by: Bub73, Nov 9, 2004, 0 replies, in forum: Ham Equipment
  15. Bub73
    Post

    RCI 2970 ALC ?

    RCI 2970 with a loud rushing noise when dead keyed and the mic gain off, like you would expect with a power mike turned full up . Also VR12 and...
    Post by: Bub73, Apr 20, 2004 in forum: General CB Services Discussion
  16. Bub73
    Post

    RCI 2970 ALC ?

    RCI 2970 with a loud rushing noise when dead keyed and the mic gain off, like you would expect with a power mike turned full up . Also VR12 and...
    Post by: Bub73, Apr 20, 2004 in forum: General CB Services Discussion
  17. Bub73
    Thread

    Rubber Ducky antennas

    Rubber Ducky antennas ; anyone check the swr on one these on the MURS freq's. I found 3 different antennas with over 3 to 1 swr. I believe they...
    Thread by: Bub73, Jan 22, 2004, 3 replies, in forum: Ham Equipment
Showing results 1 to 17 of 17
Search Again
Toggle Width

  • About Us

    The WorldwideDX Radio Forum was originally established in 2001. We pride ourselves on welcoming Radio Hobby enthusiasts of all types, while offering unbiased, informative, and friendly discussion among the members. We are working every day to make sure our community is the best Radio Hobbyist's site.

  • Like us on Facebook

  • Premium VIP Member

    The management works very hard to make sure the community is running the best software, best designs, and all the other bells and whistles. Care to buy us a beer? We'd really appreciate it!

    Donate to us!