You can now help support WorldwideDX when you shop on Amazon at no additional cost to you! Simply follow this Shop on Amazon link first and a portion of any purchase is sent to WorldwideDX to help with site costs.
Good morning!
I did a little searching, but I didn't really find anything right off.
Has anyone done anything with the TX/RX audio on the Cobra 1000GTL? From what I understand, it's the same board as the Cobra 29GTL, but I couldn't really find anything for that radio either.
Any input is...
Good evening everyone!
I was wondering if anyone has tried widening up the transmit and receive audio on a quad 6 yet? I am going to look through the schematic tomorrow to see what I can see, I just didn't know if any of you have done it yet and what the results were?
Thank you! ✌️
Merry belated Christmas to everyone!
I've got yet another radio that has me stumped, this time, I don't believe it going to be so easy...
So, I've got a new Cobra 29 LTD Classic on the bench, just finished my IRF520 conversion and tune on it, which I have done hundreds of before,(no clipped...
Good afternoon everyone!
So I've got an 88 on the bench that has me absolutely stumped.
All of the solder joint problems have been addressed, and everything was working flawlessly up until a few minutes ago when things took a dump.
It is constantly displaying 15.195 on the frequency counter...
Good evening everyone!
I'm working on a project Cobra 29, messing up around with direct injection, and so far it's working flawlessly! Super smooth audio with my rack gear!
I've been digging around and doing some research looking for a suitable upgrade for audio transformer T1. I found some...
I apologize if this has already been discussed, as I have tried searching different keywords and can't find anything, but I was wondering if anyone had the board locations to widen up the transmit and receive audio on the Uniden Washington? I wanted to ask here before. I had to sit down and dig...
Good afternoon everyone!
I was wondering if anyone on here may know what to to do increase the TX & RX bandwidth on my Icom 756 Pro III for eSSB?
I've seen a PDF online, but it was for the non-pro models. Any help is greatly appreciated! 73's
Good afternoon everyone!
I've been looking at the schematic for my President HR2510's off and on for a few weeks now, trying to figure out what capacitors I need to change to open up the transmit and receive audio. It's too damn easy to get lost in this maze of a schematic. Lol
I thought I'd...
Good afternoon everyone. I have been struggling trying to add talkback to my 55HP. I have tried the 55V mod that is listed on CBtricks every way imaginable, and still no luck. After countless Google searches and searching this forum, along with others, I have hit a dead end. The schematics are...
Good morning everyone.
I'm thinking about buying a Dentron DTR-2000L in near mint condition from a local here in Georgia.
I was wondering what the average pricing is on them? I can't find much info in Google or hardly any older eBay listings to go off of.
It has a fresh Eimac 8877 in it...
Good morning everyone. Does anyone happen to have any mod info for the Superstar JA? Like the fine clarifier unlock mod or any other mods? The SSB side is fantastic. 45w PEP with crystal clear audio. The AM side could use some help big time though. It sucks bad.
I've tried the fine clarifier...
Good morning everyone!
I know this is a bit of a hotbutton subject for some, but does anyone know of a "swing mod" for the Stryker 955? I'm trying to get a bit more average power out of one. I know with the diode/resistor combo on the AM regulator section of a Galaxy/Ranger/Connex does help...
I apologize if this is in the wrong section. Not particularly sure where to post this.
Good afternoon everyone. My buddy acquired an Armadillo Toshiba 1x2290 x 2x2879 Class C base amplifier recently, but as expected, it sounds like garbage on SSB. It does however have SSB delay, but no...
Good afternoon everyone.
Does anyone happen to have the capacitor locations and values to widen up the TX & RX audio on the PC-76? I have been searching all over with no luck. Thanks in advance!
Good morning everyone.
Does anyone happen to have the AGC improvement mod for the Anytone 5555? I've seen it mentioned on a couple different forums and other places online, but can't find the actual modification itself.
From what I gather, you have to change a capacitor out in the AGC...
This forum does not allow a single user to have more than one username. If anyone wants to change their username contact an admin and it will be done. Multiple accounts belonging to the same member will be deleted without warning.