Search results

So I am personally looking for a CPI CP2000 and accessories. It a radio I always wanted and I’ve decided to final look for one. If you have one or accessories you might want to sell let’s chat. OH, STONER radios are always welcome also! Drew

So what’s a good playback / recorder for internal installations? CRAMBONE

I found 2 different mods for the 2995DXxx but don’t want to perform the wrong on. 1)This Mod will fit all of the following ,RCI2950, 70, 85, 95-DX. All having the same PCB. 1. Remove D-63 & R-115,Using a soldering iorn. D-63 is in a row of 5, last one to the right next to VR-8,frequency adjust...

Can 2995DX be made capable of CW?

Why would a new out of box 2995dxcf show negative modulation in AM?

Anyone know the mod for this?

I was showing loss of power and lost my RX, J22 is showing a 6.5vdc on PLC. With RF Power and MIC Gain FCW and J22 Pulled I see 0 - 6 watts and with J22 plugged in I’m seeing 0 - 55 watts. Drew

Anyone have a list of the alignment points for Version 1 SR-955HP? I can only seem to find them for the newer version 2? especially the ones under the shielding ? Drew

I acquired this not working and after finding a few bad solder connections on 3 of the 4 2200 electrolytic caps and a good cleaning of tons of flux I fired it up and it’s working. I see a few different models of the DX1200 one being a “HOT PLATE”? IS THIS A CW Model? I see a small jack on the...

Radio is working perfectly as receive is very, very strong on all Bands and Channels. On AM I dead key 4.2 watts and swing 28 but on SSB I’m only seeing 10 watts. I went through the ALC c tuning procedure in the manual and I’m not getting any adjustment on R719, R719 sees 97 vdc on leg from...

Ok, I picked a D201A and it had some funky stuff going on but after replacing a crystal, 3 trimmers and the meter IC it’s working but LSB & SSB are low power compared to AM. I want to do the Neutralization but the procedure mentions a T700 tuned for max DC (where is T700 and at what point is dc...

I picked up a D201A that looks like it had some kind of mod but I can’t make it out. I’ve attacked pic of what it is. I am seeing some voltage issues on the synthesizer board that aren’t normal and I’m guessing it has something to do with the mod? Unlocked Clarifier? Thanks

Does anyone have the 11 meter upgrade info for the 69 Base Plus? Drew

Guys I have a D201A I believe is the late model from the extra trimmers on the bottom? im having a few issues. 1) meter pins far left all the time. I replaced V401 & V602 from a working D201A but still the same issue. 2) When radio is just sitting monitoring I hear the normal static on channels...

Anyone know what the TOSHIBA part number is for the Upgrade Voltage Regulator?

I am looking at the alignment procedure I attached. and have a few questions. I’m only checking and not making any adjustments at this time till I can clarify a few procedures. 6.1.1 PLL Alignment 1) USB & LSB OSC Set radio to USB TX mode. Mod off. Connect Frequency Counter to TP5 (is an...

AM is working perfect but on LSB & USB if I have the RF Power more than 25% when I key I’m seeing a full carrier? Receive sounds good on both LSB and USB. Drew

OK this is a strange one, let’s start with it is a bit off frequency on SSB but spot on in AM & FM that’s not the weird issue. when the radio is cold and keyed up at say 10 watts AM I not see a frequency read out on an external counter or scope but when I turn up power to say 30 watts it starts...

Anyone know a part number and where I can get a replacement squelch potentiometer? Drew

So I removed the channel mod and Roger beep, good news is radio works kind of. Not So good news: Set up 1) voice locks centered no modulation. 2) Frequency Counter and Oscilloscope 3) Dummy load and watt meter. Seeing: 1) CH1 RX radio frequency counter 26.9654, TX 26.9462 2) CH40 RX radio...