Recent content by Dr_DX

Arguably the best bang for your buck SSB 40 channel CB chassis ever made. 1306/1307 combo that easily will do 25 watts - runs rings around a 1969 or 2312, built in compression so the stock mic would produce full output, easy to expand and broadband. The only area where it might lag behind a...

I bet the 66" would work. But get them quick. They are discontinued.

https://www.ebay.com/itm/134675179285?mkcid=1&mkrid=711-53200-19255-0&siteid=0&campid=5336136228&customid=&toolid=10001&mkevt=1 https://www.directdepot.net/product-info.php/product-model/880-900906 https://www.12volt-travel.com/66-cb-antenna-whip-p-15442.html

Don't quote me but, I believe the original designed for CB Imaxx-2000's 3 sections were 8' long = 24' assembled. The new IMAX-2000 designed for 10 meters 3 sections are 7'8" long = 23' assembled. Either way set it up, if it works on 11 meters - Great!. If it doesn't then, you know the problem.

I agree. But with the part # maybe someone on Ebay or in the USA may carry the part. Surprisingly, NewEgg carries some Sirio parts. Or take the dimensions and see if you can find another whip that is close enough.

Correct. The 2879C is totally different. It is NOT a drop in replacement. It has very different input and output impedances. Can't over volt and is rated at 150w out. If any major amp builder would re-engineer their 2SC-2879 amps to use the HG 2879C with an AB bias (passive like Texas Star...

Only true at levels of S3 and above. Absolutely not true below... Looks good on paper, but not in reality. And if your friend is giving you S5, then he doesn't need to increase his output. But, If your friend is giving you S0~S1, then even doubling his output (+3dB) will increase his signal...

Whip for your Sirio Fighter 5000: P/N: 2507503.00 (Ø3.5x1800xØ1.5mm INOX) https://moonrakeronline.com/us/sirio-replacement-stainless-steel-whip-3-5-x-1800-x-1-5-inox

If this is a "newer" Imax 2000, then it is made for 10 meters and won't tune properly for 11 meters with out the "optimizer" or a 12" extension. https://www.ebay.com/itm/395286141066?mkcid=1&mkrid=711-53200-19255-0&siteid=0&campid=5336136228&customid=&toolid=10001&mkevt=1

He has a white one that has the extra channels in it and a CPI desk mic. You can tell by the "67" in the channel display.

Don't go by colors. Mic cord could have been changed. What ever wire the bare copper shield is wrapped around should be the audio wire. Connect it to the Ring of the phono plug. Using a continuity tester, connect the shield and the other wires. Do any of them have continuity with the mic...

mrf454 uses a 211-11 case (larger) mrf455 uses a 211-07 case (smaller) The transistors in the amp are the larger case style.

Here is the original schematic. Don't know if it helps any.

These should help. Looks like the Blue wire is your HV. Sounds like your Power supply matches Power Supply 1.

On my Magnum 6000, there are 2 pink 2 pin jumpers (near the main relay). One is a "low" drive and the other is a "high" drive (3dB). That gives you 4 different drive levels that can be set internally with the 2 jumpers. Active class A bias, 5 pole Chebyshev output filter, keying jack, cooling...