Search results

I hope I have posted this in the correct thread, please accept my apology if I have not! I just purchased a Workman W-58, and the instructions included were a Maco reprint. I am having SWR problems, I cannot get it set. I am hoping that I have missed something, and someone can spot it...

Hi everyone. I have a Sadelta Master 2002 echo/rb desk mic. I have not had any luck finding a manual for it. Does anybody know where I can find one, or can scan the one they have? I would be willing to paypal someone a few bucks if the would not mind to scan theirs. Thanks!

Hi everyone, I got a wild hair up my SO-239 and have decided to play with some "vintage" radios, I have good modern rigs, just want to play around with some old stuff just for the fun of it, and I don't care if I screw them up. I want to get a 40 channel SSB mobile. Realistic, JCPenny, or...

Hi everyone, I have an Astatic 600/Paradynamics 3 movement swr/mod/wattmeter. The 4 position switch to change wattage has sheared off flush with outside of the enclosure. Has anyone changed one of these before? I am needing a part number and a source. Thank you for any help you can...

Hi there everyone! I am attempting to put channels in a buddies rig and I am having an odd problem, I would sure appreciate your input. It is a Uniden Washington, MB8719 3 Button Board number PC-385AH. The one that I have attempted is the method where you isolate pin 10, and connect one...

Hi everyone, I don't know alot about the Astatic D-104's history, So hopefully you can help me out. I want to know which of the mics HAVE the key up tones and roger beeps? in them. Sorry if I don't have the names right, this is why I am asking! I THINK it might be the Silver K Eagles.. I...

Spotted this on Copper's website. Has anyone used one or heard one on the air? I would like your opinion before I buy one. It's a toss up between this one and a Kenwood MC-60A Copper Electronics, Inc.

Ok, so I get the rig from copper and it works real nice except for one thing. I get reverse or backwards modulation on AM. The radio had the copper alignment thing done and I am wondering if that is the problem. I have it hooked to an Astron 70 amp power supply, so I know it's getting...

Hi guys. I want to order a new RCI 2950DX from Copper. Can a guy pop the cover, change a jumper and get the extra freqs, or MUST you have them do it by putting in extra parts or something. Thanks!

I have a D-104 on it's way, it's not in my hands yet. I want to get ahold of the parts I need before it arrives. My rig supplies 12V at the mic jack, I would like to feed power to the mic with it to eliminate the 9V battery. I do not know how much current the pre-amp requires (anyone know?)...

Hi everyone. I have always wondered how to do this. I have a reallly nice microphone at 150 ohms impedance, trying to match it to a rig at the standard 600 ohms. Everything I have read says that it really should not matter. However, I get very low output from the mic. When I connect it to a...

I have one of the old KRIS power pumps that I changed the caps and diodes in. It works real nice and is in great condition. Here is a link to it that shows a photo of it. Kris Inc. Power Pump It requires a very low drive requirement, I would like to modify it to be able to be driven with a...

Hi everyone, I just picked up a Kris power pump. It is currently providing about 100 AM carrier and 200 PEP. The driver tube is a single 6JG6A driving 2 X 6LQ6. I would like to purchase a backup set of tubes for this rig before they become totally unavailable. But before I replace them I have a...

I have a Texas Star 667V I want to put on 10 meters. I want to disable the pre-driver (2SC2290) to allow for higher input power. Has anyone done this? Or know how to do it? If you are a competent tech, could you check the schematic and get me going in the right direction? Any help would...

:)