You can now help support WorldwideDX when you shop on Amazon at no additional cost to you! Simply follow this Shop on Amazon link first and a portion of any purchase is sent to WorldwideDX to help with site costs.
I have started this project and I will be using the AB-Z-1 box from Westgate. I was wondering if anyone that has used this box would be willing to share some advice or give some pointers on it. Maybe some capacitor values, component values or hardware model numbers. I know the box is pre-punched...
Does anyone have the frequency unlocking procedure for this radio? I had someone give one to me and I am not sure that it is for this radio.
Conversion:
#1- Remove cover from radio.
#2- Move the jumper JP275 to pin's 2 & 3
#3- Right behind JP275 is an empty socket marked J2.
#4- unplug the...
ANYONE HAVE ANY INFO ON THIS SWEEP TUBE AMPLIFIER? BOARDS IN IT HAVE D.J. ELCETRONICS ON THEM. IT HAS NINE 21JS6A TUBES IN IT. I WAS LOOKING FOR A SCHEMATIC FOR IT.
THANKS,
ED
Has anyone used or using the C.A.T.S. QUICK-CONNECT (QC) for their rotor? I ordered one yesterday and was wondering if anyone has used this. Here's a link to the connector http://www.rotordoc.com/
ED
I have one of these kits with the black wire broke off of it. Can anyone tell me where the correct placement of the wire is, or send me a picture of it?
Thanks,
ED
I have a Realistic TRC-465 that has the PC122 board in it. I have installed the expo 100 kit in it and I am having a little trouble getting the proper frequency to channel relation. The regular channels are fine and the clarifier slides like it should. But the high and low channels seem to be at...
I was wondering if anyone could tell me what brand of antenna this is. Notice the configuration of the static hat at the top. It is a little different shape than most that I have seen. Maybe this will give some clue to the manufactuer.
This is the link to the pictures and the antenna is listed...
Has anyone done this mod before and if so how well did it work?
"I'm sure most of you know that when you turn down your dead key using VR-10 you also turn down you peak swing. Well I've developed a simple method to enable full power swing from any power range. All you need is a 1N4001 diode...
Here’s a link to my newest homebrew project. This amp will be used with my homebrew power supply in the earlier post. The cabinet that I used is a decommissioned Harris television transmitter remote control cabinet. My dad retired from this television transmitter site and has a lot of neat stuff...
I have a RCI 2950 that I bought back in ’95 and I used it for a couple of years with good service. After that I kind of got out of radios and it sat in the closet until now. Recently I have been blowing out the dust and firing stuff up. It seems the 2950 has developed an intermittent. When the...
I would like show everybody my home brew power supply. I got the plans out of a '94 ARRL Handbook. I think the supply was originally for about 15 amps. I decided to upscale it a bit. Instead of using four 2n3055 pass transistors I went with thirty. It has a Miller 400 amp welding machine...
I am looking into buying a transistor tester. I was wondering if anyone had any suggestions on a brand and model. I would like one that will be able to test output transistors in the circuit without removing the transistors. If anyone has any ideas let me know.
Thanks,
ED
</p>
Can anyone tell me what brand of antenna I have here? I also need the setup manual for it. It looks similar to Maco V5/8 but it has an aluminum stub instead of the wire for the matching device. It also does not have the ground plane radials. The loop is 11" in diameter. I have tried to use the...
A few months ago I bought a new Signal Engineering Lightning 4+ on Ebay. After looking at how the antenna is built I am a little concerned about the plexiglass mounts for the tuning stubs. My concern is how much UV protection do they have, considering that they will be exposed to the sun. I plan...
This forum does not allow a single user to have more than one username. If anyone wants to change their username contact an admin and it will be done. Multiple accounts belonging to the same member will be deleted without warning.