Search results

Thank you I will look into it. Love the photo,,,

BOARD NUMBER KEPC-063F That is on the back of the board,,,,,,,,,,,,,,,,,,,,,,,,,,,,

Hey Bud, I recapped the 25, I have TX now, it putting out 25 to 30 watts. YES,I had some time, went recapped the whole think, and 2 caps showed up bad on the tester, did not even read them. I believe it was a 33pf 10v that was bad, and a C45 33pf 50v. OK,I have great swing, but I have NO...

Thank you so much, I really appreciate you taking your time to take care of my issue. I looked on Google, but I kept getting different answers it seemed like, and now the schematic you brought up is the one I totally understood and I was going for it. Thanks again, and if you are a Father, have...

Howdy, question for a buddy of mine, he has a Cobra 29 LX BT, the fancy L.E.D. face plater version. OK, he was doing the TDA2003A, and upon installing the Cap, ( I think that is what it is ), between t he 2 pins of the Audio Amp, the little Cap took off on him and he cannot find the little SMD...

Hey Andy, gonna get on the 25 in 5 minutes, Sat,,,Keep you informed.

Hey,quick question for a friend, he works on radio's, or is trying, where are the frequency check points on a Cobra 29 LTD Classic. I have been a bit busy helping out with senior citizens, my Father and my Mother-in law who has Alzheimer's disease. And my Father just needed a few things...

Thank you.....

Test point 3 I have my 16MHz, now where to set it at and tx or rx.

OK,I just notice on my next step is that I am not producing any 16MHz for the second half of my TX. I changed the Can, still nothing, and I do have a TA7310P in case I need one. Off to the races, going to find the missing MHz.

OK, I will do a little tracing, and see what I come up with. I will go to that section, block the next section off and trace that circuit. Been getting some use out of the Block Connectors Kit, I can block off anything I like, and go to town.

I am the same person, I have my Clone locked up, he was a naughty person, LOL

Hey, thanks, when I put my mind to something, I try my best to get it done. I know this radio is a dime a dozen, but this radio is under my skin, been up till 4 in the morning reading and trying to diagnose, the point I am trying to prove is that a broken radio can be repaired by anyone who puts...

I had to replace D2, and it is blown again,,,I put in a 30Volt Pin Diode, IN4751A. Is this a 1S1588?

OK,I am ready, it is 4:00 P.M. Central,,Indiana time,,I will be here? In and out,10 Min interavals..

Andy, about then Voltage,,I went ahead and replaced the D12, D18, D3, D20, D2,which I think it called for a 9.4 Volt, which I put in a IN4740A. On pin 4, all I have is 00.185 Volts.That may be a issue, as it seems a bunch of resistors do not have any voltage at all, 0 volts on both ends of...

Andy I understand your pain, trust me, at 40, after a fusion on my back, I had a full blown stroke. I had lost my whole right side, my face was drooping, I could not speak, still have right side weakness. OK, now in 2015, after a MRI, I was informed by the Physician reading the MRI, personally...

I have a decent amount of knowledge of the basics of a radio workings, I am a bit green on the subject, but I am learning as I go. I am not a dummy, I have the basic repair knowledge of how a CB radio works. I understand that the radio does not have the voltage in all places, but I have aligned...

Hey Handy Andy, I may have to recheck the Caps, I did replace them all, it is possible that one may have or be shorted out. I cannot set the voltage as there is no voltage upon setting the 3.2 Volts on the first procedure of the alignment according to the Cobra service manual. I shall hopefully...

Hey, the radio must be in lock, I cannot get my 3.2Volts for the VFO, I have like .261 volts, thats all I have, and it will not come out of lock it seems. I am going to peek at the Schematics and see if I can see anything down the line. What I meant on the last post is I did try to align it the...