Search results

OK, I think I did this correct to lead to No differance in it? any one think it could be a weak TA7222? Audio chip?

gee I cant find J2 for the life of me?

Any Help? where do I jump the Q73 to test it, and where do I jump through pa?

Hell Just use a echo mic, I have a SA 117. works ok I guess, But yea I already ordered the TN2510 ? I think it was? Q73.. now I can solder pretty small stuff. I have the correct tools to do it, OK,? where do I cross the transister gate draw or where? I am not understaning where to short the pa...

My 2950DX I see this is a old post, but my 2950DX volume is now starting to fade away? what was the out come of that jumper? what should I short across from the ground? any Pics? this surface mount is a pain in the butt! Is there a simple fix? thanks for any info!

OH and no talk back!

all there Yes 24 is there, it works great with a silver eagle, just not with the tug 9, I have had both wide open mic gains, with the silver eagle, and just extreemly loud every one says, guess the washington just do not likethe tug 9?

done I already tried that too! no differance?

crap I have one, and I cant even get good loud audio out of mine, everyone says I am in the dinky weeds, untill I put the silver eagle on, then Watch out, makes my uniden washington sing!

Hi, All Happy New year! I am haveing a problem with thes tug 9 I have , I can't turn it up on my uniden washington without squeeling! I did all the 470 ohm 4.7 kOhm Lpad, I also did the 10 kOHM with the .001 MFD and still squeels, And when I put my silver eagle on it, it is a audio monster ...

OK I see this is a very old thread, But I have a question?? Is there a way to wire up a 4 wire (shield red black white) stock cobra mic, the the 5 pin 148GTL Philly?

if you are talking about my question, my transistors are good, just that the low med high switch don't work and the one resistor I believe is a 150 ohm 2watt, but I don't know what the other one is, possibly a 270 ohm 2 watt? thanks

gee no answer on this question, someone has to know the value of those 2 resistors for the power select switch?

TX EIGHT HUNDRED (HELP) Gee still no answer on what components consist of the pre amp on this Linear? someone must have one that works>? or are they all junk?

well yes, I am using PDC 600 meters set on peak, and my washingtons peak at 21 on it, but I changet the finals and now I only get 18ma on both. on USB ch 19 ground to wire and pos to post, vr9 does TP8 vr8 does TP7. I know how to do Bias, but there is something wrong?

148 gtl OL I got the mic area all replaced, and working like it should stock! now I cant get more then 12 watts out of it, I tried to tune it to get max, also I tried the adjust the bias for both and whe I turn vr 8 & 9 for tp 7 & 8 I get no change, like both are stick on or about 32ma ? I...

internal amp.. Get the SX-175 by magnum, you will like it much better, I put one in my 2950 and I get 200 out of it, you can switch it also. Nice amp! copper has had it for 109.00

OK , I have the general grant, same board same linear.. OK there is a diode and a Load right there by the finals it could be them or your power regulator, if it is a B754 change it to a B817 or back to a 754. try that for now?

148 Gtl OK thanks, BUT, what about R130, I cant put that in with the wire in one of it's holes! I got 131 in I got both transistors back in. I am trying to get this old philly back to stock. thank got the clarifier has not been touched!

148 gtl OK great, I will be doing all that, thanks, I already replaced TR 24, I need to fins another one, I have 4.7k resistors, common one to stock, and also yes, the wire goes from r130 to vr7 am I suppose to remove this wire from R130 to VR7. because it is in R130's hole and I can't get a...