Search results

Radio is gone, thanks for everyones help!

what is the TX Transistor Q number?

yes I tried them all.. even CW. JUNK I guess

OK all I need to know, its in the dumpser now. thanks

Done that already Done that, same thing still recieves when pushed..and no tx Thanks

I sure would like to know what one that is. Hope it is something simple like that, but when I key up it don't even close the recieve, it still recieves when I key up ot cross the mic pins... I know what pins 4 & 5 Does! channels.. Please help

I just was given this 2510, the recieve works great, but there is no key up NOTTA nothing when mic keyed, also nothing when jumping pins 2 & 3 which I found out was the Xmit. or 1& 2 or 1 & 3. not even a tx light nothing.. any Ideas? Thanks

Thanks for your Ideas, But I gave up on it, I plugged it in and the Tune Plates were sparking, and when I turned the Tune Knob the transformer started to hum abd smoke, and it was on STBY and all other was off But power.. like it is stuck on key.. Gonna trash it, too unsafe.

And Yes the tubes are good.. probably cost a small fortune to ship with it's weight and all>

Thanks for the suggestion, but the firebird is way different, and it less agravaton to go to a dumpster than a post ofice.

Anybody have "ANY" info on this amp? hate to just trash it@!

I have a SCP amp 5 tube. (one 6lx6 driving 4 6lx6) the one who rebuilt it said it will put out 1000 watts, He was driving it with a 55v. He is the one who sugested the 2 final? but he is in FLA now relaxing for the winter, I am up here in CNY colse to Canada. in no where land. sort of close to...

then I will need a power supply , I wanted to do the final upgrade so the get the full advantage of the amp, A smal linear will fry the amp As per the tech who rebuilt it! I just need 10 watt dead key and at least 25 watts swing, the 959 and 696f only gets a 18 watt tops swing,

Thats the problem, I have a 1000 watt tube amp and the stock dx959 and tr696f do not have enough power to drive it! My Point> thank you, now please answer what I asked

Apollo 100 X-2 Help needed Hi, I was given this amp, and was told all it needed was a resistor or diode? HA, imagin that one.. does anyone have any info on these amps. pictures of the board inside and on back. There is a few componets missing as per how many holes are in it. the only thing I...

This probably has been pisted already but has anyone done this mod and have it work?? HIGH POWER MOD (30-35watts) This will work for most EPT-069610Z Boards. Install the parts listed below: 1. Q47 One additional 2sc1969 final with isolation hardware. 2. A heat sink should be bolted...

*EPT069610Z (Galaxy DX959/949/2547, Texas Ranger 696F SSB, 696F, 396, 936, 966) -Lift end of R266 that connects to D103 and C233. Solder the banded end in the empty hole where resistor was lifted and solder the other end of diode to lifted end of resistor. (CORRECTION submitted by Mav391: Cap...

I need parts for my roadtalker 934.38270700 , like the channel selector and possible the 5104 pll. so if you have a roadtalker with the model number as above. and want to sell it as parts let me know. Thanks in advanced!

Don't know what to tell you? it is doing fine with just a 4 amp fuse in it, my gereral Grant doing 225 watts, and only has 2 4 amp fuses one on + and one on -, I just looked to see, to see because of this . so back to the 959? like said above, those adjustments are sone in USB, now is there a...

Acording to the service manual those adjustments are done on Upper Side Band? not AM