Search results

I couldn’t get the schematics to load at first. Got it. 10uh 1amp. Got a 2amp coming in w/ replacement caps. Thanks.

This look correct?

Texas Star DX350 (probably the same as just about every Texas Star) None of the parts lists on cbrtricks list values for L1 or L2. I mean, shall I just grab a random rf choke ‍♂️. Needing the value and/or source for part.

Yes. It was strange because the voltage on the the trace on the board that comes from the “switched” leg of that control pot was showing 2.7v. My first thought was a shorted component was drawing down the power. The radio would actually turn on, but dim. Thats wierd.

Meet the two solder pads that should have been soldered together. Held together by a flake at one time.

[edit] Resolved below ⬇️ RX works RX audio does not work The actual volume control pot is working properly adjusting between 0-50kohm approx Tx works Tx audio (modulation and talkback) work PA Audio works when talking in mic What can I provide you with to help fix the issue. I can hear a pop...

Bump

RX works on USB and LSB Absolutely no receive on AM. Needle does not move and no RX audio. What info can I provide? Somebody was in it because the clarifier is open. Side Note: VR13 does not affect SSB audio/power and is over modulated. AM audio is perfect on the scope. Q39 Limiter is in tact.

I don’t want to spend much time dinking w/ this $150 radio but maybe someone has experienced the issue and the fix can be quick and painless. •Final shows 13.8v/13.1 at legs on TX •The transistor circled is super hot to touch all the time, key up or not.Actually, most the caps in the area are...

D85 was toast. Replaced. Works well now. I’m a little baffled at the poor sinad reading though the receive is picking up as well as my Icom though the meter doesn’t like to budge unless there’s a big signal. I calibrated S9 at -67dbm. Two separate things though. Meter could be an issue. Not as...

I will take a closer look tomorrow but I really don’t think there is any carrier whatsoever on the selected frequency showing up on the “sniffing” radio. I will check D85.

No AM TX but plenty of power on FM. Receive works. PA works. I accidentally discovered a small signal at 27.120 regardless of which channel it’s on when I looked up at my bench radio. Signal then checked on spectrum analyzer reading at coax-out and it shows up….low, but it’s there. TP3 is on...

Thank you. I’ll keep trying to figure that out.

Good point. What was I thinking? Wow, I’m still in the same boat lol. Either way, probably looking to change the value of a diode, yeah ?

Radio is about 10 years old. I think all these radios were dim and Galaxy made a change recently. I’m not sure but the new ones are brighter. It’s hard to read the channel and frequency. 8.5 volts going to this plug coming from the dimmer knob. Is there a simple mod to brighten up the lights?

LOL #smhtifotgaslam Shake My Head Til It Falls On The Ground And Starts Laughing At Me

Fixed. I don’t even know. Cut all cable ties, removed front bezel and frame, noticed the display pcb was not plugged in completely — probably my doing when removing the bezel. This setup is unique to the 3400 but is reminiscent of the 959 display board with 20 or so pins. Reflowed solder joints...

I’m going to get back to it tomorrow but it something that happened out of the blue. It seems like something isn’t switching (?)

No transmit. Receive works properly (S9 reading w/ 100 microvolts input) but virtually no receive audio - maybe 2%. Upon keyup, TX light changes to red but the receive continues to receive. Nothing changes but the light. PA works. No talkback. Connex 3400. Ranger 360015c board. How can I...

Well, got back to it and checked TR16. I have a scope that is junk. My Rigol is in for repair. I think I'll get on Amazon and get something to me asap. Should always have a working backup. Here's what I can say about TR16 right now: E / C / B RX 0/0/.7 TX 0.1/7.9/0.8 ug, that's not right...