Search results

I recently replaced toshibas with HG pills in my x-Force straight 10 pill. I removed the original unregulated power supply as the HG are sensitive to voltage swings. Planning on stacking 3 of these to replace the unregulated supply. They are dozens of different versions out there. This is the...

Anyone know if this is correct Mods for this particular power supply? Any input is appreciated.

Replaced all the Pills with matched HG’s. Verified all the transistor diode side resistors was good and in tolerance. Replaced all the combiner resistors with original 2 watt 100 ohm resistors. As well as the transistor feed back resistors. No heat except the normal transistor heat. Thanks again...

I wanted to come to the thread and Thank everyone who helped. Running really well with minimal heat. Again thank you all. 73’s.

The new set of matched HGs from ICA seems to have fixed the issue. I have only put 10 watts in and get 150 out. I still nervous about driving it with the 150 in. The built in unregulated power supply supplies about 21 vdc tapped on the 115v source. I really would like your opinion on using the...

What’s your thoughts on the variable ac voltage transformer to tame down the unregulated power supply? I have a matched set of HG 2sc2879 16D08 on the way. What effects will an unregulated power supply have on the HGs? Thanks again.

Right. The Chinese knock off actually held up for 3 years before they gave up the ghost. Do you know if HGs will fit in the same hole as these? Carl said they need a regulated power supply if I use them. I also thought about using a variable voltage and reducing the 115 vac to a lower voltage...

Tested and found 3 with a diode fault,one with leg broken off. I likely broke it removing it.3 had HFE of 2. 1 was a 3 HFE. The other 2 tested 16&17 HFE. Think the diode shorts caused the 0 output? Now got to figure out what I want to replace them with.

Roger that. I found a video building a probe on YouTube. I built the one in the screen shot. It seemed to show RF on almost every thing. So I ordered a transistor tester also screen shot. I’m going to take all 10 out and test them to be 100% for sure. I don’t mind buying test equipment. I really...

Replaced all the caps on the input side. Only thing I didn’t replace is the combiner. But it seems to test ok.

Yes Sir.

I have tested and replaced everything I can think of except transistors. Is it possible some transistors are shorted and preventing drive to reach other transistors? And how can I test them?

I tried every thing up to the point of replacing the relay. So I ordered a new one and removed it. I realized the keying circuit was still in it. Like I said I use an external keying module. The original keying components was still there just disconnected from the ground pin of the relay. Could...

I forgot to follow up on this. Cleaning the selector switch totally eliminated all issues that remained. It’s even stable on SSB other than the normal temperature drift. Thanks for all y’all have done.

Sorry to go on&on with this thing. Did you get a chance to read my last post? And one other thing is it possible for the input splitter to go bad and send the drive wattage to ground? I would think it would send the reflect to the moon if that was the case. Thanks again y’all have been super...

Will unsoldering the 3 caps from ground and doing a quick key with low power input should show some output on the meter. Right? I did the low power input from the radio and no transistors created no heat. So like you say it has to be on the input side. I’m considering replacing the relay. And...

Roger that.

Wanted to verify the suspect caps. They are the ones circled red? It’s a 10 pill so there are 5 of them. The tuning capacitor checked out. And the radio test produced no heat on the transistors. Thanks again 73’3

Thanks shock wave. I’m working 12 hour shifts and drive 1 hour each way. So I’m having little time to work on it. I’ll post what I find. Your awesome.

With the output tuning capacitor still installed the outer and inner are ringing common. Do I need to unsolder one end and recheck?