Search results

Yes he does that and I always do too. 2SC2879s always have a little bump on the center bottom of the their die cast base. I noticed when removing the transistor from my TX600 that it didn't take any effort to break the screws loose. Maybe drying out causes the compound to lose density opening up...

I had one of my amps blow a pair of Toshiba 2SC2879s. Sent it back to the builder and he said that the heat sink compound had completely dried up to powder. He said that he used ARTIC HEAT SINK COMPOUND when he did the update for me. Evidentally more expensive doesn't mean better. He had also...

It's a Crystal Filter. Located between Q5 and Q6.

$$$$$$ ??

I understand the rules and wish to enter the contest J.J. 399

Shitty neighbors can be a major PITA. When we lived in SoCal, our Korean neighbors had a tiny dog that barked 24/7. Totally annoying. I asked them politely to quiet it down. Their reply- " No speakee English." I recorded their dog for about an hour's worth to take to the city to complain. Before...

A full shot of rum (or two) warms you up good too. J.J.

Do you still have one terminal on the switch disconnected ?? If you do, then it's impossible for it to show a short in any position.

Doffo - Since the amp works when the hi/lo switch is in lo. The trouble lies in the hi portion of the circuitry. Like brandon said, check the switch. In the hi position the switch should show open. It looks like the hi contact it connected directly to the wire of the input transformer, which is...

If the 47 ohm resistor gets hot when the switch is in hi, there is a bad connection in that circuit. Or a miswire. You may have to bite the bullet and remove the board fro from the heatsink. Can you post a picture showing the connections on the hi/lo switch.

Check out the hi/lo switch. top terminal should go to the 47 ohm resistor. Middle term should go to center pin on input SO239 when the amp is in xmit. Bottom pin should not be connected to anything. If it is, disconnect it and test the amp again. Are you certain your wattmeter is accurate. Maybe...

Here's a pic of a silver streak 200 linear. Exact same board as the comet 200. The resistor that was burned shows as a 47ohm-2 watt resistor. Probably connected to the hi/lo switch and pads the input drive down in the lo position. You can check this by putting the hi/lo switch in the hi position...

Last night was amazing. A totally clear night at the farm, not a cloud in the sky. I snapped a picture. Reminded me of a night on I-40 in the Texas Panhandle on my way to California. J.J. 399

It's possible that the blocking cap is leaking some plate DC on top of the RF at higher DK levels. J.J. 399

I want to purchase a pair of 2SC2879 Red Dot toshiba transistors. From members or a biz. Just someone I can trust to sell me the real thing. Must be NOS. Not pulls. No solder on the tabs from being previously installed. PM me with price and pictures please. Thanks & 73. J.J. 399

Yes, wattage rating- wise they do cross. But being to withstand being overdriven or over-voltaged the RF pills are in a class by themselves 73 J.J. 399

Y NCA Gunsmith - RF POWER TRANSISTOR Co. (no longer in business) manufactured the RF- series of transistors that Steve used in his amps. He told me he found them at a surplus place. An overrun from a Govt mil-spec order. Sadly, - no longer available . 1446s aren't subs. Not even close. I...

RF power transistors ( 85, 100, 120) were mil spec devices made back in the late 70s - early 80s. Like Timex watches, " will take a lickin' and keep on tickin'." That TX400 is probably not a Palomar, but a TX amp made by Steve Canfield back in the day. IS THIS WHAT YOUR AMP LOOKS LIKE ?? IF IT...

I was an EBAY guy for over two decades. But their switch to AI robot customer service screwed me out of over 100 bucks from a seller who didn't send me what his photos showed. Wouldn't let me talk to a human service rep. So good-bye Ebay. . . now I'm with Amazon 100%. My wife got taken by TEMU...