Search results

Nothing in the radios Mod meter, only in my external monitor meter. Thanks for the responses. I needed to hear that someone else has the same result. I think we're hearing what the modulator (AN612) rejects.

I've added talk back to a Grant classic (almost identical inside to the Grant DX), using the modulation meter switch to bypass the diode in front of the audio chip. I use a small amount of reverb sometimes and thought it would be cool to monitor at the radio. In SSB it sounds terrible (with or...

Ya, I noticed the missing LED a while back... Haven't noticed the other issues yet. Thanks for the heads up!

Audio chip is the 10 pin next to the regulator on the same sidewall. We want to check VCO voltage before we continue. Find Test point 9 it should be it should be somewhere to the left of center towards the front half, to the left of L21. Put the radio on channel 40 AM Hook your meter to the...

If pin 3 of the *audio chip* has 1 or more volts on it, it's a telltale that the PLL loop is not locked. It also mutes outgoing audio, including the PA (pulling C232 is a hack that keeps the audio unmuted by disabling pin 3, even between channels). It's probably due to the pin voltages at the...

If pin 3 of the *audio chip* has 1 or more volts on it, it's a telltale that the PLL loop is not locked. It also mutes outgoing audio, including the PA (pulling C232 is a hack that keeps the audio unmuted by disabling pin 3, even between channels). It's probably due to the pin voltages at the...

There was a TSB on this board that added a Zener diode in that spot as a safety limiter. That one looks pretty darn corroded to me, It should operate just fine without it. I would unsolder that wire and the diode and try to clean that area up with a little wire brush. Then see if the 8 volts...

Modification #18 in the PDF from post #43.

8 should be 8v during TX (6 and 8 should toggle, RX/TX). Pin 1 is being dragged down, it should always have 8v on it. Here is a schematic from CB tricks.org. It's for a 148, the regulator circuit is nearly identical. I chose it because it's very clear and searchable. The 1st thing I would try is...

Was going to do the controlled carrier mod after finding a failing VR8. I thought the 1K dimmer pot would be a cool spot for an adjustable carrier to use with "low drive" amps. Also noticed that the schematic drawing doesn't match the trace illustration, C102 would (still) be on the emitter the...

I have a hunch that the regulator is being bogged down by one of the grey 10v caps on the board. You've already checked the usual suspects, but even if they test "good" a recap can make everything run way smoother in the end. I use nothing less than 25v caps everywhere. See if pin 1 and pin 3 of...

I started on a TRC449 today and was looking for 858 info. This post popped up. Here's something I saved a while back. If it's not allowed let me know, I'll take it down.

I dragged the PC76 out to see if it still ticked. It looks like the channel spacing is off on the modified frequencies, If you have more than the usual 40 it might get worse... 19+10k is spot on, 40+10k is 80 high and 1+10k is 80 low. I've seen AM radios being used at 300 off, so its no big...

I know this is an older thread, but I wanted to share some of my experiment results. This was with a Uniden PC76XL, it's about the same as the Cobra 29s inside. Cut the rearmost trace on the 10.24, remove C131 and bridge the cut trace with a 22pf trimmer and the lower half of the CH9 switch...

I used one (HG2312) in a pinch to repair a side mic. 29 LTD a while back, then monkeyed around with some trial and error stuff. It seems to make easy power the way it is. A clean 23pep without tweaks. These are from my notes some add a little more oomph, or help keep things sharp and clean...

I had mentioned above that I added an "NPC" mod at an earlier point. My notes on this radio were that replacing the 560ohm R282 with a 1K with a 4148 and 220ohm in series, parallel to it, works awesome. I don't "volt" the finals, I never find much to gain in it unless it has a MOSFET driver...

Okay.... Who did this??? Ohh $#!7! It was me ...... Whoops!Yep that's backwards As soon as it was corrected, everything went smooth as butter. Thanks for not cursing me out for trying stupid mods on this radio (on my post anyhow) ...lol Here's some more pics and video.