You can now help support WorldwideDX when you shop on Amazon at no additional cost to you! Simply follow this Shop on Amazon link first and a portion of any purchase is sent to WorldwideDX to help with site costs.
Since there are so many replies I’ll chime in and say that the dead key is only good on AM mode. I stated that I mainly talk SSB which doesn’t effect the power at dead key with no carrier on SSB.
I have a President Mckinely running into a Predator 225 amp. So I’m guessing about a 3 watt dead key from the radio. The only problem is that my Giant MFJ meter needs about 10 watts to calibrate for SWR. I talk on SSB mostly. I’m going to play around with the dead key on the radio while watching...
I got modulation on lo power now and high power. I'm getting 10 watts RMS. I'll check power tomorrow with another meter and check the power draw one more time. Regulator still gets kinda hot. I'm not sure if it's too hot or not. I'll check voltages as well. Bad solder joints!
I'm still hunting for a short and why I don't have modulation. I'll start again this weekend..
I checked a little last night......Basically got the radio back to where it was. I have modulation on high power with a slight hum. No modulation on low. There are a lot of bad solder joints on this...
Well I found out why my last final wasn't working. While is was unhooking the driver and finals I melted the solder and inadvertently pushed a jumper thru the board. It works now. I'll fine tooth comb it tomorrow and see if I did any other damage.
I think I will start from scratch step by step and post my results as I move along that way I won’t be jumping steps. I’m thankful there is a forum like this to help out. If it would have been my radio, I would have it sitting on a shelf broken forever. These kind of things force me to learn. I...
Well I have a better understanding of where to check for mA draw. That pic is where i set mA for my Galaxy 88, I'm working on a Connex 3400 HP mosfet version with the 360015C board. I started out with no power or modulation, then I installed new IRF520s and i got power on High and low but no...
I have read this rather large post and I can surely identify with the difficulty of repairing this particular radio. I have one on my bench that I was trying to look at for a friend blown finals and all. I have no experience at repairing radios so I was quite excited to see such a detailed post...
If you are like me you won't be satisfied with the performance of a 102 inch whip. Yes it will work, until you can get a proper base antenna. I use a Procom base antenna for about $75.00 and its up about 30 ft. I talk all over town and plenty of skip. Some guys like mower Junkie have used 102...
I have aligned this radio several times and it never transmits on the same frequency. It’s been cold, it’s been hot and in between but always drifts off. What temp do you do an alignment at or what components can I replace to make this galaxy more stable on SSB? I set the frequencies and it...
And I thought I was doing it right for once. My scope is an old BK Precision and my signal generator is one of those new cheap digital ones. The radio came out good except AM mode sounds a little low after I put the limiter back in. It’s been a learning experience but now I’m hooked.
I get to the part where you check R151 for 10.2965 and get nothing. I’ve checked all the components from the X4 crystal to R151 and everything looks good. At the crystal one side has 10.29680 and the other side is like 29.something. Help! AM carrier offset....L26
Wow is right! I just read this thread and I sounded like a little kid. We learn so much. The FT-840 had nothing wrong with it but the screwdriver I put in it. It worked great after an alignment and I have since purchased an Icom 7300.
This forum does not allow a single user to have more than one username. If anyone wants to change their username contact an admin and it will be done. Multiple accounts belonging to the same member will be deleted without warning.