• You can now help support WorldwideDX when you shop on Amazon at no additional cost to you! Simply follow this Shop on Amazon link first and a portion of any purchase is sent to WorldwideDX to help with site costs.

KRIS 600 SSB-New Project

Dmans

Sr. Member
Jan 22, 2017
1,471
1,961
173
Georgia
All,
So a good friend of mine asked me to look at his Kris Amp for him. (It had been sitting in a Truck Stop CB shop for about 6 months) I love a challenge and never pass up an opportunity to learn something-So it is on!

The initial issue he had with it was that the SSB delay was not working. I'm not sure what if anything the CB s
Shop did to it but upon initial inspection, I found it has been "screwdrivered" to DEATH.

DSCI0281.JPG

It has a decent face. The undercarriage-not so much.
DSCI0288.JPG

Sketchy wiring and soldering.
DSCI0292.JPG


First thoughts are to lose the 115v relay and convert it to a 12vdc relay, lose the microscopic coax jumpers, recap it, new bleeder resistors, new SO239's, 3 prong power cord.....................................
DSCI0283.JPG

DSCI0292.JPG


Stay tuned!

73's
David
 

Update to the Kris 600SSB

Removed the lamp cord and installed a 3 wire power cord.

It does not have a 115v relay but does have a 12vdc relay.

Found that the standby switch (a DPDT) had the center terminals shorted together and the medium voltage supply line was hooked across both poles of the switch. One side of the one of the "On" poles was wired to the 12vdc relay, the other "On" pole was wired to ground! Glad I never plugged this thing in!!

I removed the relay and using jumper wires to a 12vdc power supply tested it. It seems to work well. So it can stay.

New S0239 connectors arrived as well as some Rg316 coax. (I tried Rg58U but it was a little too stiff to make some of the turns and bends required in this chassis)

This afternoons project was cleaning up the awful high voltage supply board.
A couple of before pictures.
DSCI0291.JPG
DSCI0291.JPG


And a couple of after pictures.
DSCI0307.JPG

DSCI0304.JPG


Stay tuned!

73's
David
 

Attachments

  • DSCI0303.JPG
    DSCI0303.JPG
    115.8 KB · Views: 216
  • Like
Reactions: Shadetree Mechanic
Neat project.
I knew a couple people that had Kris amps back in 1970. Probably not the best designed amplifiers but they have nostalgic value to me although I never had one. That and the Hy-gain Afterburner amps which were common at the time.
 
Hurricane145,
Probably not the best designed amplifiers
Agreed. And not unlike today. Makers use as cheap a part/component as they can find to maximize their profit.
I still like resurrecting them though!

I spent some time on the Kris project today and rewired the standby switch so that it doesn't ground the medium voltage output meant for the driver tube. NOW when switching the Standby switch to the "On" position, it grounds half the bridge rectifier so that the high voltage/bridge rectifier circuit is complete. The other pole of the switch NOW supplies 12vdc to the keying relay-As designed. All the internal coax jumpers were replaced. The relay was also completely rewired. I did find that the way it was wired when I disassembled it would never let the unit operate. It is correct now and has been tested. I suppose after about 50 years of this things life, many a screwdriver has been inside of it. I'm not surprised at anything I have come across.

I am just trying to return it to it's as built condition with an eye on safety measures. I.e. Metal Oxide Varistors on the 115Vac lines, 3 prong power cord, fast blow fuse between the high voltage winding and bridge rectifier, a proper safety choke and cleaning up a heap of poor connections, poor wires and terrible solder joints.

So far, so good. I'm waiting on some components to rebuild the keying circuit (should have been here last Friday) but all in all it has been a fun project and a great learning experience.
(I did go through a Hygain Afterburner recently. Repaired some of my own damage and made some mods to extend tube life and give a cleaner output. It is in a thread under the "Amplifiers" heading on the forum. Now the amp sits on a shelf and collects dust. Time well spent!(y))

73's
David
 
kopcicle,
Makes me want to homebrew an amp. Been thinking about it for a while. Got some hand drawn schematics from some sleepless nights. PAOFRI's is much better than the products of my sleep deprived ventures.
Parts collecting may be the next step along with many more sleepless nights!

73's
David
 
My wife who has never soldered on a circuit board saw that HV board and said, "I could do a better soldering job than that!" She can, I had her help me when I needed a fourth hand on a chassis and she did it perfectly. I did not have to reheat it or anything. I guess I'm going to put her to work now.
 

dxChat
Help Users
  • No one is chatting at the moment.
  • dxBot:
    Tucker442 has left the room.
  • @ BJ radionut:
    LIVE 10:00 AM EST :cool:
  • @ Charles Edwards:
    I'm looking for factory settings 1 through 59 for a AT 5555 n2 or AT500 M2 I only wrote down half the values feel like a idiot I need help will be appreciated