You can now help support WorldwideDX when you shop on Amazon at no additional cost to you! Simply follow this Shop on Amazon link first and a portion of any purchase is sent to WorldwideDX to help with site costs.
I wasn't going to mention any names here but thanks again guys,thanks for the pictures that you did send me and the extra info as it will help me out a lot on building my power supply....Greg,Larry thanks for what you sent me too...now I can get started on my project......thanks again guys....my...
I use a simple home made curve tracer with my scope to make fast checks on in circuit/out of circuit transistors,diodes,resistors,capacitors,grounds,connections..sometimes it is best to just lift one end of a diode to check it or lift the transistors leads for a better check..... a good curve...
Anyone know what the brand and/or the part number is of the dual circuit breaker/switch that Fatboy uses in their 150 amp power supply? ...200 Amp Power supply ?.....
Anyone have any inside pictures of the Fatboy 100 or 150 amp or the 200 amp power supply ? (I know Fatboy has some inside...
On RG-8/213 coax,I just cut the braid back about 1/2 inch and fold it back over itself (Fan the braid out a little)then screw the pl-259 over the end of the coax while aligning the center conductor into the center pin of the pl-259 this causes the inside threads of the pl-259 to screw down on...
Here is one way to do it if you are making a lot of jumpers..and you know what you are doing !....I've made 1,000's of them this way...I use a couple of 240 watt weller guns depending on how I feel.....one of them has the regular heavy duty tip on it and the other gun has the regular heavy duty...
what is the total amount of power that you want to put in your dummy load?
That would be the first question to ask yourself....then we can give you help or point you in the right direction....the easiest is to purchase already built but sometimes it isn't as much fun as building your own and...
About that soldering iron...
I have been soldering for more than 50 years and at one time or another I have "grabed the wrong end of the soldering iron!" by mistake....it won't take you long to look at it and let go!.. but if you happen to make that mistake,grab a can of circuit cooler and...
I have a box of them around here somewhere,I think they were #1829 or simular to that,I had some 28 volt bayonet base ones just like the #47 except they had a red plastic covering over the bulb....BTW I have used bright red fingernail polish to do the same thing. makes a nice looking modulation...
I used to build those little modulation indicators using a #47 pilot lamp but later changed them out to a 28 volt bulb to keep them from blowing.I never kept them keyed but for just a few minutes or so ,just for a fast indicator during installations just for the presence of rf on a "Barefoot"...
Here in Florida on a 3 wire 110 volt single phase ac wall socket,it should be wired with the round connector to ground(Green),the larger (wider spade) connector is tied to white (which is another Ground for safety),the smaller spade is tied to black which is (hot/110volts ac).I have never seen...
Antenna Specialist "Starduster"...Omni-directional Base Antenna
Half wave Dipole.full aperture design puts more usable signal at horizon.all elements are active.5.0 db gain.VSWR 1.5.1 or less power handling capability provides 500 to 1 safety factor.
100 mph plus wind loading factor.6 ft. wing...
Hey Distortion,I think I would be looking for a better antenna than a Starduster....Is that one of the original Starduster antenna by Antenna Specialist ?...seems like such a waste of power with very little gain....BTW what are you going to do with all the Iota power supplies?
2 things.....
You sure that isn't an AMPOWER tube amp ?... maybe the first one he built.LOL
How much was the top bid ?..I must have missed seeing it listed !
This forum does not allow a single user to have more than one username. If anyone wants to change their username contact an admin and it will be done. Multiple accounts belonging to the same member will be deleted without warning.