Search results

Just rebuild the tone generator in my Golden Eagle transmitter,68t. After i changed the parts out, resistors & ne2 light. I hooked it up an every thing worked fine. After using it a little while i lost the audio. It still has a dead key, just no audio. Pin 7&9&3,on the 6bq5, have no voltage...

OK Thanks 238

Do you use 2 or 3 100x 5w resistors on the parasitic chokes? 238

Finally got my GLS 3-500 amp back together an the station put back together. Thanks for all the help. 238

O

Got a ? about the door knob caps The one on the tune is a 1000 pf , but reads 880 pf & the one on the load is a 100pf an reads 107pf. Do i need to change the one on the tune out or is 880pf close enough? I have been running the amp works ok, just wondering about the caps. 238

BJ radionut You ask about the tank coil so i took a better pic. ( Does the picture also seem to show the output coax attached to the end of the tank coil (?) maybe a P-L net) The tank coil is tied to a stand off & A wire runs from the load tuner too the stand off. The coax is solder between the...

Got the coax changed & ground at both ends. Used 393 on out put & 316 on the input. 238

I never run my stuff very hard. Cost to much. I have a roll of 213 double shield i could use in place of coax in it. I did not know if 316 i used in my Maco would work. 238

In the pic you can see black & blue wire soldered together at the relay. The blue wire goes to the stud mounted diode. The black wire goes to a switch on the front that is marked AM/AM+. On AM the switch is open & on AM+ it grounds the diode. AM+ gives it more watts. What is the purpose of...

What coax would i use in place of this? I have 316 i used in my Macos. Not sure if that is strong enough or not?

I have both your diode broads.SSB220 & JB2000 just never used them yet. Got the amp back together & it is working. Looks to be around 2500 or better. Hard to tell my probe goes to 40K, but the needle is between 2 &3 K. One switch on the front says AM/AM+ One side goes to ground the other goes...

I thought i had put the whole story about this amp on here, but i see i did not. When i got it there where 2 6lq6 tubes driving the 3-500z. But you could not tune them separate , an the tuners for the 6lq6s where on the back. So i had the 6lq6s disconnected. The SSB transformer passed away an i...

Traded from this amp in Il. about 25 years ago. Never tried it out. When i got it home, haul it home in the sleeper off my big truck, it would not key. Was not a place for a foot petal to plug in. Took to to a friend an opened it up. There was no keying broad in it. He put me one in. You can see...

This is the new parts installed Hope to try it out to night. 238

t

Got a ? about the green wires. One goes to ground the other goes to a diode. A cap hooks to the other end & goes to ground. Also 2 wires solder to the other end & each go to lights on the front an nothing else. The single black wire is solder to the green wire from the transformer. 238

This is what is going back in it. I bought ever thing to overhaul a SSB220 years ago. I have bought the diodes & resisters to rebuild the diode board. If i remember correctly it only checked at 2200 volts. I thought if i rebuild the power supply it might pep up the voltage to the tube. 238

I have a one tube, 3-500, amp i am rebuilding. It originally had a SSB220 transformer in it, but it passed away. Had a JB2000 transformer installed. I thought some one might know the voltage of the different wires. The guy just cut the other wires off. The big yellow wire is cut off also...

I can understand that. 238