Search results

They say a Ford Pinto can blow up in a rear end crash but I don't put gas in it. Is this a answer to a bad question and a ok answer????? If you are not affected why so frustrated lol.

The skip up here in Upstate NY has been relentless and unforgiving. We have a pretty good number of locals here in the Mountains where county's can have a population of 45.000. We have broke off the channel we all were on over certain words and sale of equipment etc. went wrong but in my...

I have a President HR2510 and it has one of the most pleasant " roger beep " made. Even the biggest hater's of roger beeps say they don't mind it and even forget it's there.

Well I have posted my Quad before with a CB but I have changed radio's again to the water resistant Radio Shack I bought off ebay for around $18.00 including shipping. This funny set up could compete with just about any mobile but it is their for contact between my home and especially when plowing.

Well I had some probs the first time I put this together turns out it was the radio's had intermittent problems drove me a little crazy but this one works good. I used 12' of coax and it is routed through the frame most direct route also used every inch of it. I also used the coax with the...

I have a president HR2510 and a 148GTL both radio's fully modded but the President doesn't really go below 4 watts and swings to 25 watts or more. I use them both with a antenna switch to operate between the two radio's. I use the President HR2510 most of the time barefoot but don't want to use...

A pic of my little station..

I have a President HR2510 modded that I can't get below 4 watts so I am apprehensive to use it on the RM Italy and I only use it on number 1 setting giving me about 30 watts dk but the president can swing up to 30 watts or more with audio pushing the KL-503 up to 200 watts or so, I don't want to...

On my Tacoma I finally found an antenna that has a 20 inch base so the coil is above the roof and the antenna is 6 foot 4 inches long. It is also using a spring which helped bring my swr down to 1.3 because my swr was high and I needed to lengthen the antenna so the spring helped me out with...

Never heard of that kind of WD-40 I will look this up. Also I have had my D104M6B mic for a few days so far everything is good except the glue on the decal and that's fine with me.

I have the 959DX and don't want this to be a who's got the better radio but I also own a RCI built Cobra 148GTL and it just seems an overall better radio but I do love my 959 now that has been fixed "worked a week out of the box" and modded. I wish the 959 had the NB my Cobra 29Classic LTD had I...

I have the same problem with the Astatic Road Devil mic. Is there a special silicone lubricant for electronics? I can't remember the details but I ruined a mic once using a lubricant that said safe for electronics.

Some very good info ROBB and good posts. When I receive my mic I will re-read your post ROBB and try your mod because they are on the tinny side. Their were a few posts that their were audio problems with the new ones but the switch was mentioned a lot from falling apart to very scratchy right...

My 959 had to be fixed basically right out of the box. My radio guy found a cold solder joint bad with in minutes of getting the covers off.

I just purchased "ebay" a new d104m6b and waiting for it's arrival for a President HR2510 and have found a lot of negative posts on this mic. I was under the impression this was a good mic and was surprised when I Googled this mic and seen many posts about everything that could be wrong with a...

I am not sure what radio you are using a base or a mobile as a base? If you are using a mobile radio it is common for some power supplies to cause this kind of noise.

It has been wonderful for the last few years. I have tested it against some very good ones to see what kind of readings I'm really getting and it's almost exactly the same read out. I like the illuminated and switchable meter face, with out it I would have a real hard time reading it. It has...

I did Silicone about everything even the PA and external speaker jacks but the front face plate you can't do much about.

I've been using the RM Italy's for years also.

I think you get more than you pay for with these amps. They are not the best but your not paying for the best.