Search results

Adjusting L23 L24 don’t help one makes it go quiet both ways the other one no change

UPDATE! just figured out NB/ANL off is the only time i have RX!!!! when i did the alignment procedure it had me turn NB/ANL off

I’m confused... so it’s not a good idea to see what frequency the receive is tuned at and put it on channel???

Mark can L23 & L24 ( for reference ) have her transmit and slightly adjust each and see if I can get her cleared up? would it help if I used a frequency counter? I don’t have one right now but thinking about getting one soon IDEA! Better yet I have a DX55HP which has a clarifier and a...

it’s all stock as far as I can tell... JP36 still in place (no cap installed) factory final still in it ( no mosfet ) cap over by the transformer factory size... D9 in place

i finished reading through what you sent the other day i get how squelch works now (y)... i better under stand the schematic... just to recap... i do have static now!!!! i also did replace the volume/squelch pot. because the volume control was ever so sightly bent... may have been...

i have lock on all channels and tuned For 3.2v on ch40 i have static now, very poor recieve, i can tell someone is keying but its all jumbled muffled scratchy still just red light when keying and no power out...

I wasn’t sure what category to post this in but this weekend I recently Picked up some gear with the purchase I got a AUTO ANTENNA TUNER I have a Grey viper coil with a 5ft whip, 50ft RG8X down to my shack (it literally is a shack) hooked up to antenna tuner Ok plugged in tuner got it all set...

THANKS! Tomorrow morning I’m going to look at this station monitor but I wanted to test it first and i wanted to bring this radio to test with now I can thanks a lot!

I do have plenty of those! Will do! Thanks quick side note can a circuit be to small? To put there? Also does it matter if it’s an insulated wire? The one on this radio is not insulated the one on my cobras

BUTTTTTT... the center terminal on the connector rotates with the coax!!!! Not good so I’m gonna have to change the plug (y)(y)

Ok so I recently bought a Galaxy DX 55 HP off of eBay brought it home hooked it up to my meter ( dosy... i know it’s a dosy) 300watt MFJ dummy load checked SWR ...(perfect, just for fun) boom variable dead key in spec swings 35-40 peak watts looks good... put it in my truck check receive with my...

I have one local I was looking into to buy he wants $150 for it I thought it looked really neat and could be useful... would it work for 11meter? I read it needs 35watts to work properly do you know if it would work for 11meter stock radios? Putting out 4 watts

Sooooo not a good investment???

Ya I can do that shouldn’t be bad... just mark the slug ( so you know where to put it back at... I don’t have a scope or freq. counter ) alligator clip dvm on Turn slug on each channel until it says at certain voltage I do have: Dosy meter Mfj dummy load Dvm I don’t have: Frequency...

No thud when I turn radio on with speaker plugged in to external speaker... when I work on a radio I pull the speaker cover I usually plug in external speaker

I do have red light when I key the mike

Also I’ll reiterate You can plug aux speaker in PA port, and switch radio to PA mode you can talk to your self all day long... Switch it back from PA mode and nothing no static squelch all the way down gain all the way up

this radio is spotless on the inside and out looks brand new... no noise at all from speaker no matter what( even if you touch resistor to pa and speaker port on back of radio as if your temporarily adding talk back) speaker is good ohms out perfect 8 ohm if I remember correctly like I have...

I’m assuming TR21 is working there is switch indication @ RX/TX LED indicator on front of radio