Search results

I went to his site and cannot order they might have went out of business?

I have bought a Galaxy 2517 and the switches swr, nf and nb/anl still work but the detent part not holding switches in place or location. I see that this switch block is discontinued. Has anyone any ideas about repair or replacement?

I was using my Dentron Clipperton L today and all of a sudden I noticed smoke coming from case. I shut amp off and looked inside it had a burnt smell but I could not see any signs of places where burnt. Touched transformer and it was not hot anywhere. Tubes looked good. Band switch looked a...

Our local tech helped me converting Dentron amp to just 11 meters to bypass burnt wafer switch. It was really pretty easy. Amp will not work on other bands unless jumper wire is cut or removed. The copper jumper wire makes amp run on just 11 meters. Works great.

I have a hand wired Tram d201 it is working fine on receive but as I am transmitting the transmit output drops to zero and no output. Unkey and after a minute will transmit ok again. Any ideas?

nomadradio here is a picture of inside.

Thank you nomadradio I am sure this amp was hot rodded for sure. I just know it will never be used on any other bands but 10-11

I picked up a Dentron Clipperton L and the 10 meter part of band switch is burnt up. Is there a way I can make this amp only work on 10 meters and do away with band switch???? I do not need the other bands.

I can tell one possible cause for burning out the pin link someone was over driving the amplifier. I have seen it many times. I have even did it myself

I was going to run 2 D&A transformers in parallel . In a phantom there is 850 v at tubes.

Thank you nomadradio. i am going to give it a try. Amp does not work now . I may ask more questions later.

I am looking how to identify the wiring coming out of a D&A Phantom transformer. I am going to try and use this transformer in a Apollo 500 amp that I have that fried transformer. I see 2 reds, 2 greens ,grey, and others. Thanks

I have 2 SB220 amplifiers. SB220 number one when I put some drive to it every now and then it sparks at tune capacitor. It will make a hum or spark and meter shows 2000 low and 3000 high . It does not spark or hum every time and works great other wise.... Any suggestions to problem????? The...

I have a Apollo 500 and the transformer is bad it is a 1300v can I replace it with 2 transformers out of a D&A Phantom they are around 850v i believe. Here is one from Apollo.

Thank you nomadradio I will tell my friend. It is at a shop right now that told him it was bad so we do not know if 6 or 7 wire. I will probably have to change it out for him but do not really want to I do not like working on that really high voltage stuff unless it is mine. Thanks again sir.

I have a friend that the transformer went out in his Drake L4b amplifier. It has two 3-500z tubes in it. Is there a after market transformer that will work in it? Or does anyone have one? Thanks

I have a Antron 99 and a Imax 2000 hooked up here in Michigan and both work great on 10 and 11 meters plus have weathered the hard winters here with no problems. Best antennas for the money period!!!!

I would go with the Phantom. The 6lq6 tubes are easier to find and it is easier to work on if a big if it will ever need any work. Tune it up correctly and do not drive the snot out of it and it is a great amp. I have 4 of them myself.

I am running a 4 element Gizmotchy beam. It was not expensive and easy to assemble. I am now talking farther then I ever did with my Imax 2000. I have people 35 miles away and on vertical I can hear them talking on a stock radio running no power. I like the Gizmotchy because you can add...