• You can now help support WorldwideDX when you shop on Amazon at no additional cost to you! Simply follow this Shop on Amazon link first and a portion of any purchase is sent to WorldwideDX to help with site costs.

Search results

  1. A

    cobra 25 channel display

    there is also a black wire from cir board c123 that is not connected.
  2. A

    cobra 25 channel display

    channel display was working . till i changed out the lite bulb rx/tx. now the channel display doesn't work. replaced with a new channel display and still not working. where and what would i look to check. thanks allen
  3. A

    COBRA 19DXIV PEAK &TUNE

    does anybody have information on peaking and tuning a cobra 19 DXIV. thanks al
  4. A

    Uniden PRO510XL tune and peak how to

    i have a meter. but your saying to just leave L6 alone. just clip D14. i just did front panel off and i see there is no way of putting blue lite in it.
  5. A

    Uniden PRO510XL tune and peak how to

    help just clip the d14.(right) L5 just spead the copper wire. L6 is marked on board by final, but it must be the pot full of wax correct. if so just heat wax to remove it. let me know thanks al
  6. A

    Uniden PRO510XL tune and peak how to

    what can i do to a 510 to peak it up. also is there a way to add talkback without a pa system. any help thanks al
  7. A

    galaxy 959 meter lite doesn't work

    about that your right on red to switch and black to ground. BUT if you look at the pc board behide the meter ,there is no switch on the board. JUST THOUGH I LET YOU ALL KNOW.
  8. A

    galaxy 959 meter lite doesn't work

    THANKS VERY MUCH FOR ALL THE SUPER HELP ON THIS FORUM.
  9. A

    size of frequency channel displays on radios

    does anybody know the sizes and measurements for the frequency and channel displays in cb radios.
  10. A

    galaxy 959 meter lite doesn't work

    959 there was no bulb in it. so i looked at the cbtricks web and found pcb ept55v-51z board which looks just like i got. but where they are showing bulb goes. i try it and no go with 12 volt bulb. there is no solder at those little holes either. could it be one of the resitors burn out before it...
  11. A

    galaxy 959 meter lite

    on a 959. is the meter lite a 12 volt or 18 volt. also how and where can i hook a lite up on the meter board for it to dim. where can i buy these bulbs. thanks
  12. A

    GALAXY 979 INSTALLING ECHO BOARD

    lord where did u hook up wires at for in and out audio. when i hooked up at the microphone jack board. the radio transmits for a while and then stops transmitting and no talkback. is there another place to hook up the wires at. on 959
  13. A

    cobra 148 nw st mic. wiring

    148 nw st mic. wiring question. is it a 4 or 5 pin radio. my is 4 pin. if 4 pin hooking up to a cobra microphone. pin 1 shield, 2 audio white, 3 transmit red, 4 rec. black. if its not this please let me know. thats the way i solder microphone and no transmit. thanks al
  14. A

    BANDIT ECHO GALAXY 959 HELP

    959 where would i hook the 2 hot wires to from echo board. i read in the other post about disconnecting wire from microphone board pin 2, which wire is that. any other info. would be helpful. thanks allen
  15. A

    COMPARE COBRA 29 148

    would like to know what you all think about comparing cobra 29 to a cobra 148. i'm looking for a nice night watch radio and was thinking between these two radios. i know the 148 has upper/lower which i will never use. i just worder which one could be peaked out the best.
  16. A

    GALAXY 979 INSTALLING ECHO BOARD

    it a 959 not 979 my mistake. it states. red wire to power source. orange hook up to power source ,but pass threw a switch to turn on/off. black ground . red shield is audio out from board. attach to pin 1 of microphone jack. white shield audio in. attach to pin 1 of mic. jack.
  17. A

    GALAXY 979 INSTALLING ECHO BOARD

    it says 12 or 9 volt. but best on 9 volt.
  18. A

    GALAXY 979 INSTALLING ECHO BOARD

    could some body explain how to install echo board. the board is a BB-2 board. i'm going to install the knob on the side of radio. where can i found 9 volts to hook red wire to. does the red and white wire both get hooked to pin 1 of microphone like it states. thanks al