Search results

Wavrider. I sent you a pm about the install. I'm assuming you didn't get it I'lltry again later.

Wavrider. First let me thank you for all your help. I wss involved in a car accident which left me let's say fucked up physically. My cousinjjust helped me put the station back together. That was the first step. Hopefully I'll have the antenna up no latter than the weekend.I like to keep my...

I know you mentioned cost was a factor but go for the LMR 240. Imo your choice of coax is only second to your choice of antenna. Good luck.

I'm sure if the fcc/faa and whatever other government agencies that regulate these types of flying devices, would put four of the most knowledgeable members of this site in a room and, give them an hour I'm fairly positive within that hour they'd have a solution on how to stop drones from...

Our government breaks or bends it's oe n rules daily. I would think thr chances of bringing down a jet with hundreds of people on board would be no problem for the government to jam or some how interrupt thrse droan operating signals in minutes if they we ant too. Unfoutainatly they'll wait u...

I'm not sure what frequency theses droans operate on but if my memory serves me right the r/c's used to operate on a frequency close to 27 mhz. Those were the one's that were used when I was a kid in the 70"s. I'mnot surr if those frequencys have changed. I don't understand why this...

Ever since watching Stanley Kubrick shining (about 15 time since its release). I always atemtemted to figure out what the exact transceiver is used in the movie. Shelley Longs carector (Windey torrence) uses the transceiver to contact police headquarters sevral times during the snow in. And...

I can't hep you with your schematic questions but wheather the mic's element is good or not you might want to check out w2ny. On either eBay or his own site he lists all his mic replacement parts. I'd like to share the link but my s3's Broken and untill radio shack trackes down a new one for...

Does it matter which end of the MFj 915 gets installed onto my pl 259's antenna feed? I'm assuming it doesn't matter but without any help from the instructions I just dont know. I just want to confirm if it's lettering should be right side up or upside down? I really want to get correct the...

Whats up loosecannon? I know these postings are older, but is there something on the scopes wave fourm that's letting you know the Madison's modulating over 100% or is there another piece of equipment out of picture that's letting you know the percentage? If not what exactly about the wave...

I'm hoping to install it by the weekend. My LMR 400 and pl 259 double connector (for the mfj 915) hasn't arrived yet. I'm looking forward to not only the install but I'm kinda nervously anticipating the moments right after the antenna's up, all the cables are hooked up then the moment when I key...

The bob i

A picture speaks volumes. I've owned this mic for a while and it's incredibly because out Of the seven or eight silver eagles I own wired for five pin uniden Madison's i chose this one after trying about three because every report I asked for came back "sounds excellent" so I've been using it...

I sent my LMR 400 out to have the pl 259's put on correctly by my tec. who I know will do it correctly and delete one more problem that may cause me to go nuts if I get high SWR readings and have to go nuts trying to track down the problem chances would be if it was caused by a bad pl 259 it...

I would love to do exactly that but it's juust no feasible. I definitely would like to see if there's a difference and if so what and how much the readings chsnge with or without but since the concensus seems to be if it's gonna do anything it will be positive and shouldn't affect the...

I'm fairly sure it's rated at 1500. The largest amp I'll be using is the ten tube phantom. I tune it for max smoke with 11/2 watts and see around 300 dead key 850 pep and on ssb with 12-15 I see a bit more than a kw but those readings were taken in the pep mode on a workman meter so I'm sure...

In your opinion should i install the MFJ 915 at the time of the antenna install or should i install the antenna without it. If it can only help and do no damage Im guessing go ahead and install it. This is advice I deffinetly need. I'm assuming it can only help. Am I correct? If not. Please...

Thanks for your kind words. By the way those two so 239 male to male connectors were purchased at sales@thehamshop.com for what I think was a very fare price of $6.42 including shipping. I've saved them as a favorite seller. With an exspected delivery date of 7/27. I will check out all future...

As you can see I did go ahead a purchase the suggested pl 239 male to male connector (bought two) but what I didn't mention is had my friend and tec who currently is adding new pl 259's on my main tranciver to antenna LMR 400. He's also adding a pl 259 to 25' of extra LMR 400 which was cut...

Excellent! This connector will put the MFj 915 as close to the feed point as it could possibly ever be. . I did try your link and that company was forcing me to purches four of the male to male so 239's connectors as they have a $10 minimum ordering policy (not inc. shipping) . I purchased two...