• You can now help support WorldwideDX when you shop on Amazon at no additional cost to you! Simply follow this Shop on Amazon link first and a portion of any purchase is sent to WorldwideDX to help with site costs.

Recent content by Tim Chambers

  1. Tim Chambers

    Mods for the Cobra 200GTL

    Soory for the late response;-) I just updated the mod, let me know if you have any questions.
  2. Tim Chambers

    Mods for the Cobra 200GTL

    1N914 or 4148 diode, cathode to center leg of voltage reg, 100 ohm resistor to Anode of D51. SMT, so be careful.
  3. Tim Chambers

    Anytone Ares 2

    I have not had time in the past few weeks to figure more the Ares 2, however got it on the bench again now and trying to figure out where I left off, lol;-)
  4. Tim Chambers

    Anytone Ares 2

    Hi there, I'm working on an Ares 2 at the moment, the normal mod with the AM regulator only works well with a dead key over 4 watts so far. I'll update as I make progress. ;-)
  5. Tim Chambers

    Anytone Ares 2

    If your familiar with the Diode/resistor mod I do on these types of boards, replace the resistor with a 1k variable resistor and you can quite nicely control the top end.
  6. Tim Chambers

    Anytone Ares 2

    "Swang's the Thang"! Always haters, aren't there? Haters forget that adjusting the mic gain can control the wave form pretty well. Keep up the good work!
  7. Tim Chambers

    Anytone Ares 2

    I just got an Ares 2 in today and will start learning about it including the engineering menu stuff over the next few days. I'll touch base with you and let you know what I think if you'd like.
  8. Tim Chambers

    Send me an image of the component side of the board in the AM regulator area and I should be...

    Send me an image of the component side of the board in the AM regulator area and I should be able to tell you were to solder in the parts to make it swing well.
  9. Tim Chambers

    President Ronald swing mod

    Install 1n914 or 1n4148 diode, cathode to the center leg of AM regulator trace as pictured. Make sure you don't accidentally short the leads on the cap your soldering the anode end of the diode to. Enter the service menu to set your power levels
  10. Tim Chambers

    First AM/FM FCC Approval

    President Andy 2 FCC & Thomas FCC: Lift the leg of the SMD transistor (circled in Red) pointing to rear of radio. This is the Modulation limiter. To really open the carrier modulation, solder the cathode (banded end) of a 1n914 or 1n4148 diode to the center leg of the AM regulator and solder to...
  11. Tim Chambers

    Anytone at-6666 v3

    I use a a static road devil on one of my any tones in a jeep, with excellent results. Pin one is audio pin 3 is transmit pin 5 is ground. True you lose the ability to make adjustments and change channels etc if you wire up a different microphone for it, however I'm a believer and once the radio...
  12. Tim Chambers

    motor mouth maul mod receive mod cobra 29

    Visit wwpdx and look it up, Goldfinger pioneered broadbanding TX & Rx.
  13. Tim Chambers

    That's a shame, the anytone quad 6 is a fantastic radio. If you get it back and want it done...

    That's a shame, the anytone quad 6 is a fantastic radio. If you get it back and want it done right, give me a call. Tiny's CB Shop in Oregon
  14. Tim Chambers

    Hi, yeah, busy busy, sorry. Resend the picture to my email tiny at tiny's CB shop. Com please.

    Hi, yeah, busy busy, sorry. Resend the picture to my email tiny at tiny's CB shop. Com please.
  15. Tim Chambers

    Uniden Bearcat 980 SSB NPC or swing mod help

    Don't ever buy anything that has the components hidden in epoxy or such, more than likely you're buying snake oil, all of the wires but two probably are not hooked up to anything inside the goop. put the diode and resistor in for your swing mod and you will be more than happy. If you want to...